The most critical aspect of replacing kitchen cabinet doors and drawer fronts is making them look right by centering them on their openings and keeping them square. Masking tape makes this task precise, but apply the tape lightly and pull it off gently to avoid pulling off the cabinet finish. If using a cordless drill to drive hinge screws, set its clutch to keep from overdriving the screws.
Installing New Doors on Kitchen Cabinets
•u00c2u00a0u00c2u00a0 u00c2u00a0Apply 2-inch masking tape lightly along the entire run of the cabinets. Run the tape on the bottom of wall kitchen cabinets and the top of base cabinets. Using the reveals you noted on your layout sketch, mark the door positions on the masking tape.u00c2u00a0 Snap a chalk line along the entire run so all the doors will fall on the same line. Then mark the tape where you want the edges of the doors to fall.
•u00c2u00a0u00c2u00a0 u00c2u00a0 Install hinges on kitchen cabinet doors next
•u00c2u00a0u00c2u00a0 u00c2u00a0 Hold the door on the marks arid install one screw only in the top hinge plate. Leave the screw slightly loose and use it as a pivot to align the bottom of the door. Install the lower hinge with one screw, leaving it loose. Install the remaining doors in the same fashion.
•u00c2u00a0u00c2u00a0 u00c2u00a0 Line up each door precisely and tighten the loose screws. Predrill and install the remaining screws on all doors. Remove the masking tape.
Installing Drawer Fronts on Kitchen Cabinets
•u00c2u00a0u00c2u00a0 u00c2u00a0Apply tape in the same way as for doors, and mark the tape for the exact placement of the drawer front.
•u00c2u00a0u00c2u00a0 u00c2u00a0Predrill the drawer box for the attachment screws. Insert the screws from the back of the drawer box and tighten them until just the point pokes through the front.u00c2u00a0
•u00c2u00a0u00c2u00a0 u00c2u00a0Insert the drawer box in the opening.u00c2u00a0u00c2u00a0
•u00c2u00a0u00c2u00a0 u00c2u00a0Holding the drawer front on the lines marked on the masking tape, reach behind the drawer and push it forward until the sere points indent the rear surface of the drawer front.
•u00c2u00a0u00c2u00a0 u00c2u00a0Remove the drawer and install the front, using the indented holes to position the screws. Do not over tighten the screws.u00c2u00a0 Remove the masking tape gently.
Installing Cup Hinges onto Kitchen Cabinet Doors
1. Drill 35 mm holes for the hinges. If necessary, spacing them 3 1/2 inches to center from the top and bottom of the doors.u00c2u00a0 Lay the door on a flat surface and set the hinge in the hole with the mounting plate attached.u00c2u00a0 Align the it’s perpendicular to the edge of the door and screw it into place.
2. Hold the door in place, centered on the opening, and mark the location of the mounting plates on the inside of the kitchen cabinet frame.u00c2u00a0 Disassemble the mounting plates from the hinges and mark the location of the screws.u00c2u00a0 Predrill the holes and fasten the mounting to the frame.
3. Insert both hinges in the mounting plates and tighten the adjustment screws slightly. Open and close the door and adjust its position, tightening the adjustment screws when the door is centered in its opening.
To replace the fronts on drawers on kitchen cabinets with separate face panels, unscrew the fasteners that hold the front panel to the drawer box. Align the new panel with the drawer box and fasten it.
On drawers that have front panels integral to the drawer box, clamp the front panel and remove the edges with a handsaw.u00c2u00a0 Align the box on the new panel and fasten it with screws of the proper length.